UNIVRSAL TESTING MACHINE

 

Features

• Loading accuracy as high as ±1%.
• Training roll autographic recorder supplied as standard to enable study of the behavior of  materials.
• High reading accuracy due to ELECTRONIC CONTROL PAEL.
• Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens.
• Motorized loading and unloading cycle.
• Large effective clearance between columns enables testing of standard specimens as well as structures.
• Simple controls for ease of operation.
• Safe operation ensured by means of safety devices.

 

 

Applications

 

Mechatronic Control Systems make Universal Testing Machine is designed for testing metals and other materials under tension, compression bending, transverse and shear loads. Hardness test on metals can also be conducted

 

 

Accuracy & Calibration

 

All Mechatronic Control Systems make Universal Testing Machines are closely controlled for sensitivity, accuracy and calibration during every stage of manufacture. Every Machine is then calibrated over each of its measuring ranges in accordance with the procedure laid down in British Standards 1610: 1964 and IS: 1828-1975. Mechatronic Control Systems Universal Testing Machines Comply with grade "A" of BS : 1610 : 1964 and grade 1.0 of IS -1828-1975 An accuracy of + 1 % is guaranteed from 20% of the load range selected to full load. Bellow 20% of the selected range, the maximum permissible error is 0.2% of the full reading.

 

 

 

 

Principle of Operation

 

Operation of the machine is by hydraulic transmission of load from the test specimen through DIGITAL PRESSURE TRANSDUCER to a separately housed load indicator. The system is ideal since it replaces transmission of load through levers and knife edges, which are prone to wear and damage due to shock on rupture of test pieces. Load is applied by a hydrostatically lubricated ram. Main cylinder pressure is transmitted to DIGITAL PRESSURE TRANSDUCER housed in the control panel. The DIGITAL PRESSURE TRANSDUCER gives signal to DIGITAL ELECTRONIC DISPLAY UNIT corresponding to the load exerted by the main ram. Simultaneously the digital Electronic Encoder fitted on the straining unit gives the mechanical displacement to DIGITAL ELECTRONIC DISPLAY UNIT. Both the signals are processed by Microprocessor and LOAD and DISPLACEMENT is displayed on the to DIGITAL ELECTRONIC DISPLAY UNIT

 

 

Machine consists of

 

• Straining Unit

 

This consists of a hydraulic cylinder motor with chain and sprocket drive and a table coupled with the ram of the hydraulic cylinder, mounted on to a robust base. The cylinder and the ram are individually lapped to eliminate friction. The upper cross-head is connected to two screwed columns which are driven by a motor. Axial loading of the ram is ensured be reveling the cylinder and ram of any possible side loading by the provision of ball seatings. 

Tension test is conducted by gripping the test specimen between the upper and lower cross-heads, Compression, transverse, bending, shear and hardness tests are conducted between the lower cross head and the table. 

The lower cross-head can be raised or lowered rapidly by operating the screwed columns thus facilitating ease of fixing of the test specimen

 

• Control Panel

 

The control Panel consists of a power pack complete with drive motor and an oil tank, control valves with to DIGITAL ELECTRONIC DISPLAY UNIT. A pressure transducers is connected for load indicator and a rotary encoder for elongation with resolution of 0.1 mm, is provided to measure the deformation of the specimen

 

• Power Pack

 

The power pack generates the maximum pressure of 200 kgf/cm2 the hydraulic pump provides continuously non-pulsating oil flow. Hence the load application is very smooth.

 

 

 

• Hydraulic Controls

 

Hand operates wheels are used to control the flow to and from the hydraulic cylinder. The regulation of oil flow is infinitely variable incorporated in the hydraulic system is a regulating valve which maintains a practically constant rate of piston movement. Control by this valve allows extensometer readings to be taken.

 

• Load Deflection Indicator

 

It is microprocessor based electronic control panel connected with machine using Pressure Transducer, Rotary Encoder and Electronic Extensometer. Using RS-232 serial communication port our s/w communicates with machine and get real time Load, Deflection and Extension and shows on computer.

Electronic digital displays Load Elongation and extension. Facility to hold peak - load and tare facility to make load zero. Elongation display can be set to zero. Optional printer facility. All other facilities maintained under Model UTN. Printer and PC interface.

 

 

Electronic Extensometer

 

Mechatronic Control Systems offers electronic extensometer MEE 2 to measure material extension with a resolution of one micron. Strain gauge type extensometer to be used up to elastic limit to determine important parameters like 0.1%, 0.2% proof stress and Young's Modulus.

 

 

Technical Data
Gauge Length  25 mm & 50 mm Maximum Extension  2 mm  Resolution 1 micron  Specimen Diameter 0.5 to 30 mm  Specimen Thickness up to 30 mm  Specimen Width  up to 30 mm

 

 

SPECIFICATION: